Bosch B450 Spezifikationen Seite 15
- Seite / 48
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Wire to an SDI control panel
R
Y
G
B
R
Y
G
B
3
R
Y
G
B
1
1
2
4
2
Commercial Protected-Premises Control Panel
D9412GV3 Control Panel is UL Listed For Central Station, Remote Station, Local, Auxiliary,
Proprietary, and Household Fire Alarm, and Central Station, Local, Proprietary,
Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when
communicating via a network.
System is intended to be checked by a Qualified Technician at least every 3 years.
The types of initiating circuits the control panel has been approved for are A, M, W, SS.
The types of signaling the control panel has been approved for are DAC, OT, NC, RevPol.
VOLTAGE RANGES
Open 3.7 - 5.0 VDC Short 0.0 - 1.3 VDC
Normal 2.0 - 3.0 VDC
Reset Pin
Disable all except Battery
Charging and Programming
PERIPHERAL DEVICE CONNECTIONS
RED
POWER +
YELLOW
DATA BUS A
GREEN
DATA BUS B
BLACK
COMMON
ZONEX OUT 1
ZONEX IN 1
NFPA
Style 4.0
Signaling
Line
Circuits
This equipment should be installed in accordance with the NFPA 70 (National Electrical Code) and
NFPA 72 (National Fire Alarm Code).
D9412GV3
26
25
ZONEX POWER +
24
ZONEX COMMON
23
SDI Connector
ZONEX OUT 2
ZONEX IN 2
Refer to the D9412GV3/D7412GV3 Approved Applications Compliance Guide (P/N: F01U143069)
for System Wiring Diagram, Issue A and for compatible smoke detectors. 2-wire Compatible Identifier “A”.
POWER SUPPLY REQUIREMENTS
The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
Accessory Devices. For System Loading, refer to the D9412GV3/D7412GV3 Operation
and Installation Guide (P/N: F01U143070).
(P/N: F01U143070) for Power Requirements relating to Terminals 6 and 7 .
All external connections except Terminal 5 (battery positive) are inherently power
limited. Requirements for battery standby time might reduce allowable output.
Battery: Replace every 3 to
5 years with one or two Model
D126 or D1218 12 V Lead Acid
Batteries.
Operation Monitor LED
Pulses when Normal
Flickers when Ringing
GREEN
Point 8, S3 Option
Closed = 1 kΩ EOL
Normal Operation
Open =AB-12 UL
Bell Box 220 kΩ
25
Point 3
Point 4
1614
Point 1
Point 2
11 13
Point 5
Point 6
17 19
Point 7
Point 8
21
20
22
Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2007:
UL Listed and Classified control unit Model D9412GV3, D7412GV3, or D7212GV3;
UL Listed and Classified keypad Model D1256, D1257, D1260, D1255, D1255R, or D1255RW;
UL Listed Local Bell
WARNING!
To prevent risk of
electric shock,
disconnect AC
power and
telephone lines
before servicing.
181512
Not suitable for remote station protected premises services where separate transmission circuits
are required for fire, supervisory (when applicable) and trouble signals when using D185.
Commercial Protected-Premises Control Panel
D9412GV3 Control Panel is UL Listed For Central Station, Remote Station, Local, Auxiliary,
Proprietary, and Household Fire Alarm, and Central Station, Local, Proprietary,
Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when
communicating via a network.
System is intended to be checked by a Qualified Technician at least every 3 years.
The types of initiating circuits the control panel has been approved for are A, M, W, SS.
The types of signaling the control panel has been approved for are DAC, OT, NC, RevPol.
VOLTAGE RANGES
Open 3.7 - 5.0 VDC Short 0.0 - 1.3 VDC
Normal 2.0 - 3.0 VDC
Reset Pin
Disable all except Battery
Charging and Programming
PERIPHERAL DEVICE CONNECTIONS
RED
POWER +
YELLOW
DATA BUS A
GREEN
DATA BUS B
BLACK
COMMON
ZONEX OUT 1
ZONEX IN 1
NFPA
Style 4.0
Signaling
Line
Circuits
This equipment should be installed in accordance with the NFPA 70 (National Electrical Code) and
NFPA 72 (National Fire Alarm Code).
D9412GV3
26
25
ZONEX POWER +
24
ZONEX COMMON
23
SDI Connector
ZONEX OUT 2
ZONEX IN 2
Refer to the D9412GV3/D7412GV3 Approved Applications Compliance Guide (P/N: F01U143069)
for System Wiring Diagram, Issue A and for compatible smoke detectors. 2-wire Compatible Identifier “A”.
POWER SUPPLY REQUIREMENTS
The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
Accessory Devices. For System Loading, refer to the D9412GV3/D7412GV3 Operation
and Installation Guide (P/N: F01U143070).
(P/N: F01U143070) for Power Requirements relating to Terminals 6 and 7 .
All external connections except Terminal 5 (battery positive) are inherently power
limited. Requirements for battery standby time might reduce allowable output.
Battery: Replace every 3 to
5 years with one or two Model
D126 or D1218 12 V Lead Acid
Batteries.
Operation Monitor LED
Pulses when Normal
Flickers when Ringing
GREEN
Point 8, S3 Option
Closed = 1 kΩ EOL
Normal Operation
Open =AB-12 UL
Bell Box 220 kΩ
25
Point 3
Point 4
1614
Point 1
Point 2
11 13
Point 5
Point 6
17 19
Point 7
Point 8
21
20
22
Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2007:
UL Listed and Classified control unit Model D9412GV3, D7412GV3, or D7212GV3;
UL Listed and Classified keypad Model D1256, D1257, D1260, D1255, D1255R, or D1255RW;
UL Listed Local Bell
WARNING!
To prevent risk of
electric shock,
disconnect AC
power and
telephone lines
before servicing.
181512
Not suitable for remote station protected premises services where separate transmission circuits
are required for fire, supervisory (when applicable) and trouble signals when using D185.
Figure 4.6: Using terminal strip or interconnect cable wiring on an SDI control panel (GV3 Series control panel shown)
Callout ᅳ Description
1 ᅳ Compatible SDI control panel (GV3 Series control panel shown)
2 ᅳ B450
3 ᅳTerminal strip wiring
4 ᅳ Interconnect cable
4.5.2
Conettix Plug-in Communicator
Interface
Installation | en 15
Bosch Security Systems, Inc. Installation and Operation Guide 2013.09 | 02 | F.01U.282.875
- Table of contents 3
- 4 en 4
- Introduction 5
- 6 en 6
- System overview 7
- Bus address settings 8
- Bus address label 9
- Installation 10
- Conettix Plug-in Communicator 11
- Interface 11
- Installation 11
- 12 en 12
- Wire to the control panel 13
- Wire to an SDI2 control panel 14
- Wire to an SDI control panel 15
- 16 en 16
- Configuration 17
- 18 en 18
- Configuration 19
- 20 en 20
- Configuration 21
- Use USB to configure the B450 22
- Configuration 23
- 24 en 24
- Log into the USB interface 25
- 26 en 26
- USB Main menu 27
- USB menu structure 27
- USB menu 28
- Configuration 29
- 30 en 30
- Configuration 31
- Use SMS to configure the B450 32
- Configuration 33
- %1;1=B450;2=secret123;15=3; 34
- %2;19=1;! 34
- Firmware Update page 35
- Figure 5.13: File navigation 37
- Configuration 37
- 38 en 38
- LED status indicators 39
- F01U273558) 43
- Technical specification 44
- Certifications 45
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450
(4 Seiten)
(12 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.136 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern