Bosch FPA-5000 Betriebsanweisung

FPA-5000 OPC-ServerFSM-5000-OPC en User Guide

Step-by-Step ConfigurationFSP-5000-RPS1. Open the FSP-5000-RPS programming software.2. In an existing 2.x configuration select “Nodes” in the tree vie

Panel Controller MPC-xxxx-B or MPC-xxxx-C1. Insert the ADC-5000-OPC card into one of the vacant address card slots.2. Go to the node that has been ass

TroubleshootingIf the configuration of the FSM-5000-OPC server doesn’t work with the FPA-5000 network trythe following:– Confirm on the panel controll

Technical dataSupported OPC standards:– DA 2.0– AE 1.01Other Standards– “BIS Common Requirements” (Bosch standard).Supported operating systems:– Windo

X at the end stands for full duplex-capable cable.FL at the end stands for fiber optic cable.For example: 100BASE-TX indicates a Fast Ethernet connect

AppendicesAppendix A.1 - State Table 1OPC Item Value Internal PanelCompound StateDescription600 Invalid 601 Normal 602 Fault 603 Fire 604 Fire Pre

628 Not enough addressspaceAddress card changed and now there are lessaddresses licensed than points configured629 Address card tamper The countdown a

656 Isolate Activationfailed 657 Isolate Alarm 658 Normal Day Mode 659 Fault Day Mode 660 Alarm Day Mode Table 7.1: Appendix A.1 - State Table 1Ap

25 On P226 Acknowledgement P327 Malfunction P428 Malfunction power supply P529 Switch Off P630 Alarm verification TEL31 Address Blocking ASP32 Trigger

59 Alarm Pre-Level (UGM) R-P460 Fire-Int Thermo (UGM) R-P561 Fire-Int Optics (UGM) R-P662 Fire-Ext Thermo (UGM) R-TEL63 Fire-Ext Optics (UGM) R-ASP64

93 Triggering Disarmed A794 Mains Fault95 Battery FaultTable 7.2: Appendix A.2 - State Table 220 en | Appendices FPA-5000 OPC-Server2013/05 | 2.0 | F.

Bosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 GrasbrunnGermanywww.boschsecurity.com© Bosch Sicherheitssysteme GmbH, 2013

Table of contents1Purpose 42Preconditions 63Installation 73.1 Installation of FSM-5000-OPC Software 73.2 Remote Access to the FSM-5000-OPC Server from

PurposeThis document contains information on accessing and controlling FPA-5000 networks via OPCusing the FSM-5000-OPC server. It is designed to aid i

RSN 002RSN 003Ethernet192.168.1.2255.255.255.0FPA_OPCRSN 004Cat. 5Cat. 5CANRSN 003RSN 001switchRSN 001 Figure 1.2: FPA-5000 network controlled by an O

PreconditionsThe following must be available to set up an OPC server in an FPA-5000 network:– FPA-5000 network with MPC-xxxx-B or MPC-xxxx-C– ADC-5000

Installation Installation of FSM-5000-OPC SoftwareTask: FSM-5000-OPC is running on a PC.Notice!.NET Framework 2.0 must be installed to run FSM-5000-OP

All of the following settings refer to the PC running the OPC server.Notice!The following steps are based on the Windows XP operating system. For all

3. Select on the right side: Network access: Sharing and security model for local accounts.4. Right click on this selection to open Properties and cho