Bosch K2200 Series Installationsanleitung PDF herunterladen (Seite 46)

K2200 Series | Installation Guide | 6.0 Configuration and Testing EN | 46

Bosch Security Systems | 7/03 | 17375 1.3 / 46513C

Note:

It is recommended that the dial-back times are set using

Readykey for Windows.

5. Telephone number 1 for dial-back.

Press [ENT] to save, press [NXT] to go on

6. Telephone number 2 for dial-back.

Press [ENT] to save, press [NXT] to go on..

7. For this feature to operate, P must be specified

for Setup - Remote Acknowledge, Dialback and

Comms Protection.

PROTECT COMMS N

This feature allows dial-up communications to be

established only when the master keycode sent

by the CNC matches the master keycode stored

in the door controller.

Type [N] to allow the next dial-up to be

accepted. The next master key that is sent by the

CNC will be accepted by the door controller and

stored. All future dial-ups must have a match

between this code and the one sent by the CNC.

Press [ENT] to save, press [NXT] to go on.

8. Up to 16 Hayes-compatible modem control

characters can be entered here.

You should only need to use these if the modem

connected requires more than the standard

programming provided by default.

Do not put

any characters in here unless instructed to do

so by Bosch Technical Support.

To enter characters not provided on the keypad,

you can use the [•] key, followed by the

following letters:

Table 22: Key Combinations to obtain keys

not on keypad

[•] key +

Result

A &

B \

Q ?

S *

End of setup. Press [ESC] to return to CMD

prompt.

6.1.8 Event Mode

Five options are provided which can prevent certain

types of transaction being sent by the door controller

to the administration system. This can be useful in a

busy system to speed up the communication of more

important events, or on dial-up systems to keep

connect times short.

1. From the CMD prompt, type [T] then press

[ENT].

CMD_T

2. This allows programming of Request to

Exit, Request for Entry event filtering.

Type Y and [ENT] to ignore these events.

FRGT RTR N

Press [ENT] to save, press [NXT] go on.

3. This allows programming of Free Exit event

filtering. Type Y and [ENT] to ignore these

events.

FRGT FREE EXIT N

Press [ENT] to save, press [NXT] go on.

4. This allows programming of filtering of events

generated by time profiles. These are all

"automatic/auto" events, e.g. Automatic Lock

and Auto Zone Disable. Type [Y] and [ENT] to

ignore these events.

FRGT TIME EVNT N

Press [ENT] to save, press [NXT] go on.

5. This allows programming of "allowed" or

positive events - Access Authorized,

Entry Authorized, Exit out of Hours

and Exit Authorized. Type Y and [ENT] to

ignore these events.

FRGT POS TRANS N

Press [ENT] to save, press [NXT] to go on.

6. This allows programming of all events where

access is denied (negative events - No Access

: 'reason' events. .

Type [Y] and [ENT] to ignore these events.

FRGT NEG TRANS N

Press [ENT] to save, press [NXT] go on.

7. This allows programming of positive transaction

dial-back for door controller 1 (i.e. the door

controller connected directly to the modem).

DIAL D/C1 DR----

Type the door number (reader channel number)

for which you wish dial-back to be initiated in

the case of a positive event occurring followed by

[ENT].

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Bosch K2200 Series Installationsanleitung Seite 46

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch K2200 Series