Bosch Solution 16plus Spezifikationen

Solution-16 Operators Manual ISSUE 1.60

Arming The System There are several different ways to arm the system depending on whether you are leaving the premises and require all active zones to

Arming In STAY Mode 1 STAY Mode 1 is only used when the perimeter and unused areas of the premises need to be armed to detect any would be intruder f

Arming In STAY Mode 2 STAY Mode 2 is only used when the perimeter and unused areas of the premises need to be armed to detect any would be intruder f

Disarming The System When you enter the premises after the system has been armed in AWAY Mode, or if you have armed the system in STAY Mode 1 or STAY

Figure 3: CP5 LED Codepad Showing Audible Alarm Buttons Codepad Duress Alarm A codepad duress alarm is used as a silent hold-up alarm. This will only

Isolating Zones Isolating zones allow you to manually disable one or more zones before arming the system. Once a zone has been isolated, access is al

Code To Isolate The method will restrict only those user codes that have the priority level ‘Code To Isolate’ set to be able to isolate zones. There

Zone Indicator Description 1 Battery Fail 2 Date & Time 3 Sensor Watch 4 Horn Speaker Fail 5 Telephone Line Fail 6 E2 Fault 7 Zone 16 In Alarm

Zone 16 In Alarm - Partitioned Systems Only This fault will register when Zone 16 has registered an alarm condition. The AUX indicator will display

Turning Output Devices On/Off This feature is only applicable if your security company has programmed an output that can operate external devices (ie.

!"#$%&"'()*+Operators Manual Copyright  2002 by Electronics Design and Manufacturing Pty Limited, SYDNEY, AUSTRALIA Document P

Testing There are various functions that allow you to test that your system is operating correctly. Horn Speaker Test 1. Press and hold button 1 unti

Day Alarm Day alarm allows a combination of zones to be monitored during the disarmed state by beeping the codepad buzzer. Only your installer can pr

Partitioning Your control panel can be partitioned or split into four individual areas. Each areas can be operated from one ‘Master Partitioned’ code

Operation Of Codepads In Partitioning Area Addressable Codepad Operations If you have a system that has been partitioned with ‘Area Addressable’ eig

Remote Arming Via Telephone This feature allows you to arm your system from any remote location via the telephone. For obvious security reasons, the

Operating The System Via A Touch-Tone Telephone If the system has been installed with an optional DTMF command module, the system can be operated via

Domestic Dialling Domestic dialling can be used to call your mobile phone or a relative/friend in the event that your control panel has activated an a

Programming Domestic Telephone Numbers If your system has been set-up for domestic dialling, this function allows any Master Code holder to program t

Domestic Voice Message Reporting The system can be configured by your security company to report to your mobile phone when an alarm occurs and playbac

Basic Pager Reporting This feature is only applicable if your system is reporting to a pocket pager. Basic pager reporting requires some interpretati

Table Of Contents INTRODUCTION...

Figure 6: Basic Pager Display The example above shows that the transmission has come from the control panel that has an ID number of 678 and that z

PET Pager/SMS Reporting The system can be configured by your security company to report to your mobile phone via SMS messaging or a pocket pager when

Glossary Of Terms Term Description Alarm Condition Is when your alarm system is armed and one of the detection devices have been violated. A 24-ho

Term Description Hand Held Remote Control Can be used to remotely operate your system via hand held transmitters (Also known as RF keyfobs). Is

Term Description User Code A user code is the personal identification number that the operator uses to arm and disarm the system. Zones A monit

Warranty Statement Electronics Design and Manufacturing Pty Limited warrants this product to be free from defects in material and workmanship for a pe

Advice To Users The Austel permit that has been issued for this product is subject to the following conditions: • The Solution-16 control panel may

Installation Notes Installation Company Technicians Name Technicians Telephone Number Installation Date Warranty Expires Panel Software Vers

Zone Descriptions This allows you to describe each zone and tick which zones have been programmed to be automatically isolated in STAY Mode 1 or have

User Code Names Master Code Master Code Default = 2580 User #1 Y User #17 User #2 User #18 User #3 Us

Telephone Line Fail...

Entry / Exit Times Entry Time 1 Exit Time Entry Time 2 Entry Guard Time Entry Time 3 Entry Time 4 Arming Options Single Button Arming

Isolating Method Standard Isolating YES NOCode To Isolate YES NO Communication Options Back To Base Reporting YES NOPanel Account Number

Index 2 24-Hour Zones... 34 A Access Denied ...

N New Zealand Telepermit Notes...36 O Off Indicator...

BASIC PAGER REPORTING ...29 Basic Pager Displa

Introduction Congratulations on selecting the !"#$%&"'()* control panel to protect you and your property. So that you can obtain

Codepad Indicators Figure 1: CP5 Eight Zone LED Codepad Figure 2: CP5 Eight Zone LCD Codepad The codepad is the communications interface between yo

STAY Indicator The STAY indicator is used to display that the system is armed in STAY Mode 1 or STAY Mode 2. The STAY indicator will also flash in u

FAULT Indicator The FAULT indicator is used to display that the system has detected a system fault. Refer to Fault Analysis Mode on page 16 for addi