Bosch DS7400XiV4-EXP Spezifikationen PDF herunterladen (Seite 116)

DS7400XiV4-EXP | Reference Guide | 7. Reference Materials EN | 116

Bosch Security Systems | 1/05| 4998154963B

Special Emergency Key: The emergency key (key B)

at the bottom center of the keypad entry area is the

Special Emergency Key.

• If programmed, the key will activate a

supplementary or an auxiliary type alarm when

pressed for 2 seconds.

• It may be programmed for a silent, steady, or

pulsed alarm.

Panic Key: The emergency key (key C) at the bottom

right of the keypad entry area is the Panic Key.

• If programmed, the key will activate a panic alarm

when pressed for 2 seconds; nothing will display at

the keypad to indicate an alarm.

• It may be programmed for a silent, steady, or

pulsed alarm.

The Special Emergency Key and the Panic

Key will generate the alarm sounders only

in the area of the keypad that activated that

Key.

7.2.8 Custom Arming Programming

Custom Arming - [PIN ][#][4]: If programmed, the

[PIN][#][4] command sequence may be used to custom

arm the system by arming only certain zone functions.

• For example: All interior zones plus some

perimeter zones may be bypassed while leaving

some of the perimeter armed.

7.2.9 Force Arming

Force Arming: If programmed, allows violated zones

to be force armed. When force arming, the user must

enter the usual arming command followed by the

[Bypass] key. This automatically bypasses zones that are

violated and programmed as bypassable.

• Fire zones, supervisory zones, keyswitch zones,

waterflow zones, and non-bypassable zones can not

be force armed.

• See Section 5.9.14 Force Arming and Ground Fault

Detect Programming for more information.

7.2.10 Ground Fault Detect Programming

• Ground Fault: If programmed, this function will

allow the system to detect ground faults. This

function is required for fire panels and will be

forced on when the control panel is in the

commercial fire mode.

• See Section 5.9.14 Force Arming and Ground Fault

Detect Programming for more information.

7.2.11 Commercial Fire Mode Programming

In a system that includes both fire alarm

and burglar alarm devices, the system must

produce distinct sounds for fire and burglar

alarm conditions either by using different

indicating appliances or by using distinct

cadences for the same appliance.

Commercial Fire Mode: When in Commercial Fire

Mode, the control panel will perform some functions

(for example, communications) differently to conform

with commercial fire regulations.

• See Section 5.9.15 Commercial Fire Mode

Programming for more information.

Water Flow Zone Delay: This is the amount of time

a water flow zone must be violated before the control

panel will initiate an alarm.

• The delay is necessary to accommodate normal

changes in water pressure.

• If the water flow initiating device incorporates its

own time delay, do not program the control panel

unit to exceed 120 seconds combined time delay.

Pulsing Fire Zone: This is a zone programmed to

output a pulse for a fire alarm in the normal manner

(one second ON, one second OFF).

California March Time: This is a zone programmed

to output a pulse for a fire alarm in the California

Time cadence (ten 1/2 second pulses, followed by one

second of quiet time).

Temporal: This is a zone programmed to output a

pulse for a fire alarm in the Temporal cadence (three

1/2 second pulses, followed by one second of quiet

time).

Single Keypad Use: The keypad should be used on

the keypad bus and be mounted to the front of the

control panel enclosure OR if within the same room as

the control panel equipment with the wire run in

conduit (or equivalently protected against mechanical

injury) within 20 ft. (6.1 m) of the control panel

equipment.

• This keypad should be assigned as address 1.

Multiple Keypad Use: One keypad only must be used

on the option bus, at any address from 11 to 14, and

must meet the following requirements:

• The keypad must be mounted to the front of the

control panel enclosure OR mounted within the

same room as the control panel equipment and the

wire is run in conduit (or equivalently protected

against mechanical injury) within 20 ft. (6.1 m) of

the control panel equipment.

1 2 ... 111 112 113 114 115 116 117 118 119 120 121 ... 143 144

Kommentare zu diesen Handbüchern

Keine Kommentare

Bosch DS7400XiV4-EXP Spezifikationen Seite 116

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch DS7400XiV4-EXP