Bosch B450 Installationsanleitung Seite 108
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
If this option is selected, any zone pulse count readings are handed over and accumulate to
any zone that is activated during the same arming cycle. Zone pulse count handover only
operates with zone pulse count time options 8 to 15.
Notice!
24-Hour Zones cannot receive any handover pulses from other zones. 24-Hour Zones can hand
over pulses to other zones.
8 – Handover Delay to Be Sequential
If this option is selected, handover delay is sequential (that is, in numerical order from lowest
to highest). If the sequence is broken before the Entry Time expires, an alarm occurs. If this
option is not selected, handover delay follows the entry path if a Delay Zone is activated first.
System Options 4
Item Location Option Default New
System Options 4 0495 1 = Panel to power up disarmed (if power
reset)
2 = Arm/disarm tracking on power up
4 = Reserved
8 = Reserved
2
1 – Panel To Power Up Disarmed
If this option is selected, the control panel powers up in the disarmed state when the battery
and AC MAINS are reconnected after the system is powered down.
If this option is not selected, the system is always powered up armed in AWAY Mode.
2 – Arm/Disarm Tracking on Power Up
If selected, the control panel keeps its current armed status in non-volatile memory. If the
control panel is restarted due to a power failure, the control panel returns to being armed or
disarmed as it was before the power failed.
Example
If the system is disarmed when the system is powered down, the system returns to the
disarmed state when the system is powered back up.
Consumer Options 1
Item Location Option Default New
Consumer Options 1 0496 1 = Test reports only when armed
2 = Test report after siren reset
4 = Auto arm in STAY Mode 1
8 = STAY indicator to display day alarm status
0
1 – Test Reports Only When Armed
If this option is selected, Test Reports (Contact ID Event Code 602) are only sent when the
system is armed. It is no longer necessary to send a Test Report with an Arm/Disarm Report
every day.
Most commercial premises are open during the working week, so a Test Report is not
necessary because Arm/Disarm Reports are sent at the programmed time. If you want to
manually send a Test Report, press and hold [9] button until two beeps sound.
2 – Test Report after Siren Reset
11.4
11.5
108 en | System and Consumer Options Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450
(20 Seiten)
(24 Seiten)
(96 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern