Bosch B450 Installationsanleitung Seite 38
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2. Press [7][2][1] to access the Network Module menu.
3. Set both modules to 2 – Used, Config.
4. Continue to press [-] until you return to Confirm to Save Parameter Changes.
5. Press [#] to save the changes.
6. Power off the control panel, then power it back on.
7. Press [7][2][1] to return to the Network Module menu.
8. Set both modules to 1 – Used, Not Config.
9. Continue to press [-] until you return to Confirm to Save Parameter Changes.
10. Press [#] to save the changes.
B426 Conettix Ethernet Communication Modules
The B426 Conettix Ethernet Communication Module is a four-wire powered SDI, SDI2, or
Option bus device that provides two-way communication with compatible control panels over
IPv4 or IPv6 Ethernet networks.
Typical applications include:
– Reporting and path supervision to a Conettix Communications Receiver/Gateway.
– Remote administration and control with A-Link Plus or our Remote Security Control
application for handheld devices.
– Connection to building automation and integration applications.
The B426 is built for a wide variety of secure commercial and industrial applications. Flexible
end-to-end path supervision, AES encryption, and anti-substitution features make B426
desirable for high security and fire monitoring applications. It is capable as a stand-alone path
or it can be used in conjunction with another communication technology. For Fire Monitoring
applications, the B426 meets UL864 and NFPA72 standards for Single Communication
Technology with approved Bosch control panels.
B450 Conettix Plug-in Communicator Interfaces
The B450 Conettix Plug-in Communicator Interface is a four-wire powered SDI2, SDI, or option
bus device that provides two-way communication with compatible control panels over
commercial cellular networks using a plug-in communicator (available separately).
Use the B450 in combination with a plug-in communicator for primary or backup alarm
communication, remote control panel programming and other remote applications. The B450
supports Conettix IP protocol with full authentication, 256 bit AES encryption and resistance
to Denial of Service attacks. Use the B450 to add cellular network communications to existing
or new commercial security and fire installations.
Switch addressing
Use the address switch to assign a bus address or setup for USB or SMS configuration where
required. The address switch allows bus address selection.
Configuration
For most installations, the default B450 settings allow installation with no device programming
required. For customized network settings, the B450 supports a USB configuration menu, or
configuration via SMS.
When the B450 is running in version 3 compatibility mode, it reports its module type as a
B426. Networking parameters can be configured using A-Link. When the cellular specific
parameters need to be modified, use USB or SMS to configure the module directly.
When the B450 is running in version 4 compatibility mode, it reports its own product type.
Both networking parameters and cellular specific parameters can be configured using A-Link.
4.10
4.11
38 en | Accessories Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450
(20 Seiten)
(24 Seiten)
(96 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern