Bosch B450 Installationsanleitung Seite 134
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
This output operates when the AC MAINS fails. The output is reset when the AC MAINS is
restored. This output operates regardless of whether Option 2 in Location 494 is selected or
on TEXT codepad the Menu 341 "Ignore AC Fail" is enabled.
1,5 Low Battery
This output operates when a Dynamic Battery Test detects the battery failed or the battery
voltage is below 11.0 VDC. The Dynamic Battery Test is performed every 4 hours after the
system is powered up and every time the system is armed. This output is reset only after a
Dynamic Battery Test reports that the backup battery voltage is normal.
1,6 Horn Speaker Monitor Fail
If the Enable Monitoring of Horn Speaker option (2) in Location 492 is selected or option
“Horner Speaker Fault Monitor” (TEXT Codepad Menu 3-4-3) is enabled, this output operates
when the horn speaker is disconnected. The output is reset when the horn speaker is
reconnected.
1,7 Sensor Watch Alarm
This output operates when the Sensor Watch fault occurs. The output is reset when this fault
clears.
1,8 Codepad Medical Alarm
This output operates when a user activates a Codepad Medical Alarm by pressing [7] and [9]
at the same time on the remote codepad. This output is reset when a valid User Code is
entered at the remote codepad.
1,9 Codepad Fire Alarm
This output operates when a user activates a Codepad Medical Alarm by pressing [4] and [6]
at the same time on the remote codepad. This output is reset when a valid User Code is
entered at the remote codepad.
1,10 Panic Alarm
This output operates when a user activates a Codepad Panic Alarm by pressing either [1] and
[3] or [STAY] and [AWAY] at the same time on the remote codepad , or when a keyfob Panic
Alarm is activated by pressing ARM button and DISARM button together on the learned keyfob.
This output is reset when a valid User Code is entered at the remote codepad, or ARM or
DISARM button on the keyfob is pressed to reset alarm.
1,11 Codepad Duress Alarm
This output operates when a user activates a Duress Alarm by adding a 9 to the end of the
User Code used to disarm the system. This output is reset the next time the system is armed.
1,12 Codepad PIN Error – Access Denied
This output operates when the wrong code is entered more times than allowed. The number
of incorrect attempts allowed is programmed in Location 424 or TEXT codepad option "Access
Retry" (Menu 2-3). This output is reset when a valid User Code is entered after the codepad is
unlocked.
1,14 Horn Speaker (Output 1 Only)
This output operates only on Output 1. Use this output for one or two 8 Ω horn speakers.
To enable monitoring of the horn speaker, select Option 2 in Location 492.
1,15 Sirens Running
This output operates for the duration of the Siren Run Time programmed in Location 479.
When the sirens are activated, this output is reset when the Siren Run Time expires. The relay
output (Output 4) is set by default for this operation.
2,0 Strobe Operating
This output operates when an alarm occurs and is reset when a valid User Code is entered.
The strobe output (Output 3) is set by default for strobe operation and is programmed to
reset automatically after 8 hours.
2,1 Silent Alarm
134
en | Programmable Outputs Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450
(20 Seiten)
(24 Seiten)
(96 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern