Bosch B450 Installationsanleitung PDF herunterladen (Seite 133)

If the output is activated by Entry Timer 1, Entry Timer 2, or Entry Guard Timer for STAY Mode,

the output is reset when the Entry Time or Entry Guard Time expires or the system is

disarmed.

If a zone programmed for Day Alarm is activated when the system is disarmed and Day Alarm

is turned on in the area to which this zone is allocated, the output is reset when the zone is

resealed or Day Alarm is turned off in the area to which this zone is allocated or the system is

armed. You can turn Day Alarm on and off by holding down [4] or selected from the menu on

KP.

0,13 Exit Warning + Entry Warning + Day Alarm Resetting

This output operates when the system is armed, regardless of whether zones are sealed or

unsealed, until Exit Time expires or the system is disarmed.

The output operates again during Entry Time and is reset when Entry Time expires or the

system is disarmed. The output also operates during the Entry Guard Timer for STAY Mode

time and is reset when the Entry Guard Time expires or the system is disarmed.

If a zone programmed for day alarm is activated when the system is disarmed or Day Alarm is

turned off in the area to which this zone is allocated or the system is armed, the output is

reset when the zone is resealed or Day Alarm is turned off in the area to which this zone is

allocated or the system is armed. You can turn Day Alarm on and off by holding down [4] or

selected from the menu on KP.

0,14 Day Alarm Resetting

This output operates when a zone programmed for Day Alarm is activated while the system is

disarmed and Day Alarm is turned on in the area to which this zone is allocated. The output is

reset when the Day Alarm zone is resealed or Day Alarm is turned off in the area to which this

zone is allocated or the system is armed. You can turn Day Alarm on and off by holding down

[4] or selected from the menu on KP.

0,15 Day Alarm Latching

This output operates when a zone programmed for Day Alarm is activated while the system is

disarmed and Day Alarm is turned on in area to which the zone is allocated. The output is

reset by pressing [AWAY]. You can turn Day Alarm on and off by holding down [4] or selected

from the menu on KP.

If the control panel is partitioned, you can reset only this output on the area codepad to which

the zone is allocated.

1,0 Day Alarm Enabled

This output operates when Day Alarm is enabled in any one used area. The output is reset

when Day Alarm is turned off in all used areas.

You can turn Day Alarm on and off by holding down [4] or selected from the menu on KP.

Three beeps indicate that Day Alarm is turned on, two beeps indicate that Day Alarm is turned

off.

1,1 Telephone Line Fail

This output operates when the built-in telephone line fault module detects that the telephone

line is disconnected longer than 40 sec. The output is reset when the telephone line is

restored continuously for 40 sec. This output does not operate unless Option 1 in Location

176 is selected or the function "Telephone Line Fault Indicator” (Menu 3-5-4) is enabled.

1,2 Kiss-off Received

This output operates after the control panel successfully transmitted to the receiving party, or

else the output is reset.

1,3 AUX Power Supply Fail

This output operates when the 12V SDI2 BUS devices power supply or 12V zone or output AUX

power supply fails. The output is reset when all fault AUX power supply above is reset..

1,4 AC Fail

Control Panel

Programmable Outputs | en 133

Installation Guide 2014.07 | 00n | F01U298026

1 2 ... 128 129 130 131 132 133 134 135 136 137 138 ... 151 152

Kommentare zu diesen Handbüchern

Keine Kommentare

Bosch B450 Installationsanleitung Seite 133

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450