Bosch B450 Installationsanleitung Seite 128
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Programmable Outputs
The control panel has four fully programmable outputs on the main printed circuit board and
one programmable output that operates the codepad buzzer. The four outputs are set by
default to operate as an alarm device, fire alarm verification, strobe, and internal screamer.
Programmable outputs require four parameters to operate correctly.
Parameter Description
Event Type The Event Type specifies when an output is activated. Enter the
code for the Output Event Type into the two corresponding
locations for the output.
Polarity Polarity determines whether the output operates for the duration
of the event, pulses for the duration, operates only once (one
shot), or latches on.
Time Base/Time
Multiplier
The Time Base and Time Multiplier parameters determine how
long and how often the output operates.
Table 15.1: Output Parameters
Output Programming
Item Location Default New Item Location Default New
Output 1 (Default = Horn Speaker) Relay Output (Default = Sirens Running)
Event Code 0436 1 Event Code 0454 1
Event Code 0437 14 Event Code 0455 15
Polarity 0438 0 Polarity 0456 1
Time Base 0439 0 Time Base 0457 0
Time Base Multiplier 0440 0 Time Base Multiplier 0458 0
Time Base Multiplier 0441 0 Time Base Multiplier 0459 0
Output 2
(Default = Fire Alarm With Verification)
Codepad Buzzer
(Default = Entry/Exit Warning and Day Alarm)
Event Code 0442 2 Event Code 0460 0
Event Code 0443 7 Event Code 0461 13
Polarity 0444 10 Polarity 0462 2
Time Base 0445 2 Time Base 0463 1
Time Base Multiplier 0446 1 Time Base Multiplier 0464 0
Time Base Multiplier 0447 5 Time Base Multiplier 0465 1
Output 3 (Default = Strobe – Reset After 8 hrs.)
Event Code 0448 2
Event Code 0449 0
Polarity 0450 6
15
15.1
128 en | Programmable Outputs Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450
(20 Seiten)
(24 Seiten)
(96 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern