Bosch B450 Installationsanleitung Seite 39
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
LEDs
Three LEDs provide status and troubleshooting information about the module and its
connection.
LED Description
Heartbeat Indicates the system status of the B450 and its connection to the
control panel.
RX Indicates when an inbound packet is received on the bus.
TX Indicates when an outbound packet is transmitted on the bus.
Mounting considerations
Find a location with acceptable signal strength on your wireless network. Mount the B450
Conettix Plug-in Communicator Interface into the interior of a compatible enclosure via the 3-
hole mounting pattern using the supplied mounting screws.
Wiring considerations
The B450 connects to a control panel using a data bus connection via the module’s terminal
strip, or the module’s interconnect wiring connectors.
For data bus powered installations outside the compatible control panel enclosure, follow the
maximum wiring distances in the technical specifications. For further installations power from
a compatible auxiliary power supply.
Using the network communication modules
Location 81 enables/disables the external network module 1.
Location 82 enables/disables the external network module 2.
If with text codepad, go to menu 721 Network Module to enable/disable the network module.
When the value of the location above is 0, the external network module is disabled
accordingly.
When the value is 1, the corresponding network module is enabled, but the control panel
won't configure parameters of network module.
When the value is 2, the corresponding network module is enabled, and the control panel will
configure the relevant parameters to network module.
Location 81
Location 82 Reports to
Receiver 1
Reports to
Receiver 2
Will control panel configure
parameters of Network
Module?
Value = 0 Value = 0 No report will be sent by
network module.
No
Value = 1 Value = 0 Sent by network module1 No
Value = 2 Value = 0 Configure Network Module 1
Value = 1 Value = 1 Sent by
network
module 1
Sent by
network
module 2
No
Value = 1 Value = 2 Configure Network Module 2
Value = 2 Value = 1 Configure Network 1
Value = 2 Value = 2 Configure Both Network
Modules
4.12
Control Panel Accessories | en 39
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch B450
(20 Seiten)
(24 Seiten)
(96 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern