Bosch SF8172V Spezifikationen PDF herunterladen (Seite 103)

Bosch

29-5

• Due to camera limitation, when setting 1080P for MJPEG stream on the Autodome Jr 800HD, it

is shows 1920x1072.

• If observing some delay in live and recorded video on Victor Client – we recommend configuring

the settings on camera GUI as:

Go to Settings/advanced/camera/encoder profile/Profile 1/Expert settings:

• GOP structure = IP

• Iframe distance = set slider to the same FPS value configured on the VE NVR.

• Due to a camera issue for some Bosch cameras, for example Auto Dome Easy II IP, the camera

has an interlacing issue when using 4CIF resolution. In order to resolve the

issue, the camera

must be set to CIF resolution

(on both the camera GUI (Settings/advanced/camera/encoder

profile/Profile 1/Video resolution ) and VE NVR video stream configuration.

Known Issues

• The FPS is only 2.75 when MJPEG streaming (25 fps) is in use. It is a known camera limitation.

Confirmed with Bosch support that for most of the Bosch cameras FPS can only reach up to 5

FPS.

• Audio and video is not synchronized with MJPEG stream on victor client. This is due to the

MJPEG stream limitation on the FPS only reaching a low rate.

• When setting Brightness and Contrast on the NBC-265-P, it returns an error message. This is

because it uses different CGI from other cameras, so these properties and functions are not

supported.

• Frequent Video Loss for Bosch Dinion HD 1080p D/N IVA is caused by the default NVR storage

setting. The recommended mount option when setting up the NVR is:

nofail,noatime,nodiratime,attr2,nobarrier,noquota,allocsize=4M

• GOP structure should be set to “IP” prior to adding cameras to NVR. Failure to configure this

setting may cause videoloss or issues with victor playback.

•

• If the network connection between the NVR and the camera drops and then established again,

this may result in the camera/device not restarting correctly. The camera should be restarted

• Due to an NVR web client known Issue, when Stream 2 is enabled with the same codec as

Stream 1, the setting is a copy of the Stream 1 settings. But Bosch dual H.264 stream support

has a different resolution list. So when the client applies, it shows and applies a different

resolution value on Stream 2.

• Due to the NVR web client known issue, when setting the resolution for the second H.264

stream, set it on the advance edit page. This is due to the fact it is a copy setting of H.264 stream

1 on camera list page with editing status, and real available resolution may not be included in the

copy of the resolution list.

• Due to camera known issue, for Dinion HD 1080P D/N IVA camera, set resolution 4CIF

(704x480) on H.264 Stream 1 and 768x432 on H.264 Stream 2, then the user only can get an

actual resolution 704x432 for H.264 Stream 1. And set resolution 768x432 on H.264 Stream 1

and 4CIF (704x480) on H.264 Stream 2, user can only get actual resolution of 704x432 for

H.264 Stream 1.

• There is a green line at top of victor Unified Client live stream on Bosch AutoDome Jr 800HD.

This is a camera issue.

• Playback video stuttering when rewinding/forwarding the H.264 video from AutoDome 800 Jr.

The camera setting is: NTSC, H.264, 1920x1080, FPS=30. Camera's firmware version is

39500570.

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 ... 174 175

Kommentare zu diesen Handbüchern

Keine Kommentare

Bosch SF8172V Spezifikationen Seite 103

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch SF8172V