Bosch DS7445i Betriebsanweisung Seite 28
- Seite / 54
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 28 P/N: 49211C © 2002 Detection Systems, Inc. All rights reserved. DS7240/DS7220 User's Guide
PART II: KEYPAD USER’S GUIDE: DS7447i LCD KEYPAD
4.38 Auto-Forward Off Setup
I can perform this function.
I cannot perform this function.
Key Sequence: [#] + [8] + [4]
Description
Use this function to program the Auto-Forward Off
sequence that cancels the redirecting of all incoming
calls to another telephone number when you turn the
system off.
Procedure
1. Enter a valid user PIN.
2. Enter [#] + [8] + [4].
The keypad then scrolls through the following:
Auto-Forward Off
Setup mode.
Enter digits for
Auto-Forward Off
For ‘pause’ (P),
Press On.
For ‘flash’ (F),
Press Perimeter
A and C keys
Move cursor.
To delete a digit,
Press B key.
To view and edit
Press Bypass.
To stop edit
Press Bypass
To exit
Hold #.
3. Enter the Auto-Forward Off sequence.
4. Press and hold the [#] key to exit this function.
4.39 Auto-Forward On/Off
I can perform this function.
I cannot perform this function.
Key Sequence: [#] + [8] + [2]
Description
Use this function to turn the Auto-Forward feature on
or off as necessary.
Procedure
1. Enter a valid user PIN.
2. Enter [#] + [8] + [2].
If Auto-Forward is already on, the keypad
displays the current status and any available
options. To turn Auto-Forward on, press the [1]
key. To turn it off, press the [2] key.
3. Press the [#] key to exit this function.
4.40 Remote Arming with Telephone, Area 1
I can perform this function.
I cannot perform this function.
Description
This function controls the built-in telephone arming
feature for Area 1. When enabled, the panel answers
the phone on the programmed ring count.
Procedure
When the panel answers the phone:
• If the panel is armed All On, Perimeter Only or
Partial On, it sounds three beeps and starts
the handshake tone for remote programming.
• If the panel is Off, it sounds one short beep,
waits approximately 3 seconds, and then starts
one long beep. Press and hold the [5] key* for
two seconds immediately after the first short
arming beep and before the long beep begins.
• The panel will arm if it detects a [5] key press
from the telephone (All On with Delay, faulted
zones are force-armed). The panel waits
sounds three beeps (new-armed state) and
then hangs up.
* If arming from a cell phone, quickly press the [5] key
three times. If pressing and holding the [5] key for two
seconds from a house (landline) phone does not
produce a tone long enough to arm Area 1, retry by
quickly pressing the [5] key three times.
Remotely disarming the panel cannot be done
with a telephone.
This feature is not permitted for UL
applications.
- User’s Guide for the 1
- MY ALARM COMPANY IS: 2
- Contents 3
- Part I: Introduction 4
- 3.0 Keypad Overview 5
- 3.2 Keypad Tones 6
- 3.3 Keypad LED Functions 6
- 3.4 Function Key Sequences 7
- 3.5 System Events 7
- 3.8 Logging Out of the System 7
- Part II: Keypad User’s Guide 8
- 4.7 Set Partial On Zones 10
- 4.10 Force Arming the System 12
- 4.11 View Faulted Zones 13
- 4.12 Bypass Zones 13
- 4.13 Date and Time 14
- 4.14 Change PIN 14
- 4.15 Change Others’ PINs 15
- 4.17 Add a PIN 16
- 4.18 Delete a PIN 17
- 4.19 Renew One-Time PINs 17
- 4.20 Check System Troubles 18
- 4.21 View Alarm Memory 18
- 4.22 View System Trouble 19
- 4.23 View Zone Trouble 19
- 4.24 System Test 19
- 4.25 Walk Test 20
- 4.26 Reset the System 21
- 4.27 Turn Chime On/Off 21
- 4.28 Select Chime Tone 21
- 4.29 Select Chime Zones 22
- 4.30 Extend Auto-On Time 22
- 4.31 Change Skeds 22
- 4.32 Change Outputs 25
- 4.33 Remote Program 26
- 4.34 All Areas Off 26
- 4.35 All Areas On 26
- 4.36 Move to Area 27
- 4.37 Auto-Forward On Setup 27
- 4.38 Auto-Forward Off Setup 28
- 4.39 Auto-Forward On/Off 28
- 4.41 View Log 29
- 5.1 Silence Alarms 30
- 5.2 Keypad Adjust 30
- 5.3 Turn the System Off 30
- 5.4 Turn the System All On 31
- 5.7 Set Partial On Zones 32
- Flashing Armed LED 33
- 5.10 Force Arming the System 34
- 5.11 Bypass Zones 35
- 5.12 Date and Time 35
- I can perform this function 36
- 5.17 Delete a PIN 39
- 5.18 Renew One-Time PINs 39
- 5.19 Check System Troubles 40
- 5.20 View Alarm Memory 40
- 5.21 View System Trouble 40
- 5.22 View Zone Trouble 41
- 5.23 System Test 41
- 5.24 Walk Test 42
- 5.25 Reset the System 42
- 5.26 Turn Chime On/Off 42
- 5.29 Extend Auto On Time 44
- 5.30 All Areas On 44
- 5.31 All Areas Off 44
- 5.32 Auto Forward On/Off 44
- 5.34 Remote Program 45
- Part III: Reference Materials 46
- 7.0 Panel Event Descriptions 47
- 10.0 Maintenance and Service 52
- 11.0 Power Failure 52
- 12.0 How to Clean the Keypad 52
- 13.0 Glossary 53
- Detection Systems, Inc. 6/02 54
- P/N: 49211C Page 54 of 54 54
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Bosch DS7445i
(175 Seiten)
(44 Seiten)
(8 Seiten)
(64 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern